![cisco switch configuration cisco switch configuration](https://image.slidesharecdn.com/cisco2960basicconfigurationvlanconfiguration-140617054858-phpapp02/95/cisco-2960-basic-configuration-vlan-configuration-1-638.jpg)
- #Cisco switch configuration how to#
- #Cisco switch configuration manuals#
- #Cisco switch configuration pdf#
- #Cisco switch configuration password#
- #Cisco switch configuration Pc#
![cisco switch configuration cisco switch configuration](https://networklessons.com/wp-content/uploads/2014/01/cisco-smb-switch-vlan-management.png)
In this step, you will examine the default switch settings, such as current switch configuration, IOS information, interface properties, VLAN information, and flash memory. Step 2: Verify the default switch configuration. A Cisco 2960 switch first placed into service has no networking configured. Switch(config-if)#auto qos voip trust cisco-phone (specifically for Cisco IP phones) No IP addressing parameters are configured yet. Please see the secondary configuration above. Trunk port configuration example to carry the different VLAN tags between two devices on the same physical link. Platform: Catalyst 2960-X, Catalyst 3560. Software: 12.X, 15.X, IP Base, IP Services, LAN Base, LAN Light.
#Cisco switch configuration Pc#
* With newer IOS it is not required that a switchport connecting a phone piggybacking a PC to be configured as a trunk specifically. Trunk port configuration (Cisco) Technology: Switching. Switch(config-if)#switchport access vlan Switch(config-if)#switchport access vlan - Voice VLAN Switch(config-if)#switchport trunk native vlan - Data VLAN
#Cisco switch configuration pdf#
You are free to download any Cisco Switch manual in PDF format.
#Cisco switch configuration manuals#
Switch(config-if)#switchport trunk encapsulation dot1q Cisco Switch manuals are introduced in database with 1138 documents (for 14016 devices). Supermicro switches do not create VLANs by default except for VLAN 1. Protocol based VLAN is enabled by default.
![cisco switch configuration cisco switch configuration](https://www.computernetworkingnotes.org/images/cisco/ccna-study-guide/bsc-topology.png)
Users can change the native VLANs for trunk interfaces as explained in section Native VLAN on Trunk. Several lines of the interface configuration is fairly common, first we see the interface description followed by the access vlan config and switchport mode. Switch(config)#mls qos - Enabline QOS globally on the switchĬase 2: PC's connected via switchport behind the IP phone. Supermicro L2/元 Switches Configuration Guide 9 VLAN 1 is configured as the default native VLAN for all trunk interfaces.
![cisco switch configuration cisco switch configuration](https://i.ytimg.com/vi/VotXqv6Vdrc/maxresdefault.jpg)
Switch(config-if)#switchport voice vlan - Voice VLAN in case of phone Switch(config-if)#switchport access vlan - data VLAN in case of PC Switch(config)#interface GigabitEthernet (The ip address should be one of the useable IP addresses of the phone or data subnet) Switch(config-if)#ip address - IP address Subnet Mask Switch(config-vlan)#name Voice - description of the VLANĬreating VLAN interfaces (SVI's) and assigning IP address to them:
#Cisco switch configuration how to#
Switch(config-if)# channel-group 5 mode onĬheck how to configure PAgP on Cisco switch.Sample configuration for Voice and Data deployment on a SwitchĬase 1: Phone and PC's on different/dedicated switch ports on the switch Switch>enable Switch (config)configure terminal Switch (config)hostname S1 S1 (config)exit Configuring Vlan on Switch With the VLAN you can reduce size of the broadcast-domain, and you can divide your network into different small network segments. With this mode the switch or the other end switch will not recognize any problem with ether channel and will not tell about problem. You can use the following configurations for setting host-name on Cisco Switch. Switch(config-if)# channel-group 5 mode paasiveĪll static EtherChannels, that is, the port is not running LACP messaging but static bundling. Next, we’ll assign a hostname to the Cisco switch. Type Enable into the console, then enter the following command: Switch configure terminal Switch (config).
#Cisco switch configuration password#
LACP mode that places a port into a passive negotiating state, in which the port responds to LACP packets that it receives but does not initiate LACP negotiation. Under the factory default setting you do not need to enter a password simply type Enable and then enter the Global Configuration Mode of the Cisco switch. Switch(config-if)# channel-group 5 mode active Switch(config)# interface fastethernet 0/1 To configure port as an LACP active mode: LACP mode that places a port into an active negotiating state, in which the port initiates negotiations with other ports by sending LACP packets. Switch(config)#interface port-channel 5Then you need to assign the physical ports and specify LACP mode. There are few LACP modes: “active”, “passive” and “on”.įirst, to configure logical etherchannel interface: Switch#configure terminal Eight of the ports are in active mode and the other eight are in hot-standby mode. You can configure maximum 16 ports to form a channel depending on IOS version and platform. LACP allows Cisco switches to manage Ethernet channels between switches that conform the 802.3ad protocol. Link Aggregation Control Protocol IEEE 802.3ad (LACP) is an open standard of Ethernet link aggregation. Technology: Switching Area: Link aggregation Vendor: Cisco Software: 12.X, 15.X Platform: Catalyst platforms